Extension development
ClamWall Howto

[quote user="Heini_net"]

 but shoutd mercury use an external daemon or its better if mercury run clamwv automaticially ?

[/quote]

I'd say it doesn't make much of a difference. ClamWall just runs ClamD/FreshClam with the --config-file= parameter, which points to the config file you have configured in ClamWall. This allows to run ClamD/FreshClam from a location which is different from c:\clamav but otherwise it's pretty much the same.

Best regards,

Nico
[quote user="Heini_net"]<P> but shoutd mercury use an external daemon or its better if mercury run clamwv automaticially ?</P>[/quote] I'd say it doesn't make much of a difference. ClamWall just runs ClamD/FreshClam with the --config-file= parameter, which points to the config file you have configured in ClamWall. This allows to run ClamD/FreshClam from a location which is different from c:\clamav but otherwise it's pretty much the same. Best regards, Nico

Hi,

 does the clamwall PDF-Manuall contain all what i must do ? 

 Because i dont know if clamwall running because i can't find any exe files.. i have enter the setting wich load clamwall by mercury as daemon.

 It is already installed as deamon while i have run the install-file ??

 and how i can test clamwall??

<P>Hi,</P> <P> does the clamwall PDF-Manuall contain all what i must do ? </P> <P> Because i dont know if clamwall running because i can't find any exe files.. i have enter the setting wich load clamwall by mercury as daemon.</P> <P> It is already installed as deamon while i have run the install-file ??</P> <P> and how i can test clamwall??</P>

Did you install ClamAV as well? Clamwall is a daemon for Mercury to interface with ClamAV. Links to ClamAV and instructions can be found on the Clamwall homepage.

Check the Clamwall log file to find out what's happening if you want to test it.

/Rolf 

<p>Did you install ClamAV as well? Clamwall is a daemon for Mercury to interface with ClamAV. Links to ClamAV and instructions can be found on the <a href="http://www.ararat.cz/eng/show.php?clamwall" target="_blank" mce_href="http://www.ararat.cz/eng/show.php?clamwall">Clamwall homepage.</a></p><p>Check the Clamwall log file to find out what's happening if you want to test it. </p><p>/Rolf </p>

Here are a Entry from the logfile:

 

  20080129 185449.255 MG000024 From: <>
  20080129 185449.255 MG000024 To: xxx@xx.xx
C 20080129 185459.755 MG000024 ClamD version:
C 20080129 185459.755 MG000024 ClamD started
C 20080129 185459.755 MG000024 FreshClam started
E 20080129 185500.740 MG000024 ClamD not responding!
_ 20080129 185500.755 MG000024 Done! (11501)

whi ClamD is not responding??

&lt;P&gt;Here are a Entry from the logfile:&lt;/P&gt; &lt;P mce_keep=&quot;true&quot;&gt;&amp;nbsp;&lt;/P&gt; &lt;P&gt;&amp;nbsp; 20080129 185449.255 MG000024 From: &amp;lt;&amp;gt; &amp;nbsp; 20080129 185449.255 MG000024 To: &lt;A href=&quot;mailto:xxx@xx.xx&quot;&gt;xxx@xx.xx&lt;/A&gt; C 20080129 185459.755 MG000024 ClamD version: C 20080129 185459.755 MG000024 ClamD started C 20080129 185459.755 MG000024 FreshClam started E 20080129 185500.740 MG000024 ClamD not responding! _ 20080129 185500.755 MG000024 Done! (11501) &lt;/P&gt; &lt;P&gt;whi ClamD is not responding??&lt;/P&gt;

It seems Clamwall hasn't been able to get ClamAV running after all. Try starting ClamAV manually to see if you get any error messages. Check settings in the conf files (directory paths etc, see the Clamwall manual).

/Rolf 

&lt;p&gt;It seems Clamwall hasn&#039;t been able to get ClamAV running after all. Try starting ClamAV manually to see if you get any error messages. Check settings in the conf files (directory paths etc, see the Clamwall manual).&lt;/p&gt;&lt;p&gt;/Rolf&amp;nbsp;&lt;/p&gt;

Looks like ClamD was started, but apparently closed directly after. What ClamAv distribution are you using? If it's the one from hideout.ath.cx make sure you have the MSVC8SP1 runtime library installed. If not, you can get it either from Microsoft directly or also from the hideout.ath.cx page. Besides, as Rolf already suggested try starting clamd in a cmd window and look for the error message which you most probably get.

Best regards,

Nico

Looks like ClamD was started, but apparently closed directly after. What ClamAv distribution&nbsp;are you using? If it&#039;s the one from hideout.ath.cx make sure you have the MSVC8SP1 runtime library installed. If not, you can get it either from Microsoft directly or also from the hideout.ath.cx page. Besides, as Rolf already suggested try starting clamd in a cmd window and look for the error message which you most probably get. Best regards, Nico

hi,

 i have try to run ClamD manually and get one error message about missing daily-data files. After them i have run clamfresh, that loads this missing file.

 after them clamd is running without any problems.

 but shoutd mercury use an external daemon or its better if mercury run clamwv automaticially ?

&lt;P&gt;hi,&lt;/P&gt; &lt;P&gt;&amp;nbsp;i have try to run ClamD manually and get one error message about missing daily-data files. After them i have run clamfresh, that loads this missing file.&lt;/P&gt; &lt;P&gt;&amp;nbsp;after them clamd is running without any problems.&lt;/P&gt; &lt;P&gt;&amp;nbsp;but shoutd mercury use an external daemon or its better if mercury run clamwv automaticially ?&lt;/P&gt;
live preview
enter atleast 10 characters
WARNING: You mentioned %MENTIONS%, but they cannot see this message and will not be notified
Saving...
Saved
With selected deselect posts show selected posts
All posts under this topic will be deleted ?
Pending draft ... Click to resume editing
Discard draft